Oatey 50683 1/4lb Silver Safe Flo SolderHow to install a Delta tub spout with pull down Diverter. You can remove your tub spout by twisting it counter-clockwise to see how your existing spout is threaded, if desired, but it is recommended you leave the spout on if you might need to use the tub before your new spout arrives. You may need to slide a putty knife underneath the spout to loosen the putty first. Remove the O-ring from the brass adapter. If you can see a tiny screw on the underside of the spout, you have a slip-on tub spout with a set screw. Scrape off old caulk. Within those two types are different attachment options: slip-on with setscrew or the threaded type. Use a tubing cutter (view example on Amazon) to cut the pipe stub to a three- or four-inch length. The slip-fit assembly consists of a two-piece clamp, two washers, and an O-ring. A front end threaded tub spout can be used with either a tub valve without a shower, or with a tub valve that has a shower diverter built into the tub valve. Hand tighten the tub spout onto the brass adapter. Many brands, like the Moen Roman tub faucet, will follow a similar removal procedure. Spread a bead of silicone around the edge of each hole in the surround and install the faucet plate and tub spout. Because spouts are different sizes and the plumbing behind the wall is installed at different depths, it's necessary to measure and purchase or make a pipe when installing a new spout. Apply some silicone caulking around the edge of the where the pipe meets the wall to prevent water from dripping behind the spout and into the shower wall. Measure Measure the length of your tub spout from the back edge of the spout to the front where the threads start on the inside of the spout. The tub spout itself has a plastic inner core with coarse threads to match the brass adapter male threads, allowing the tub spout to have room for adjustment forward or backwards determined by the position of the adapter on the pipe. 6 spouts: $611.51: $751.67: Bathtub Spout Installation Labor, Basic Basic labor to install bathtub spout with favorable site conditions. If your Tub Spout has a set screw holding it in place, be sure to remove that prior to rotating the Spout off. Slide the new spout over the pipe, making sure it’s snug to the wall, and tighten the set crew. These particular adapters can also be used on copper tubing by sweating the adapter onto the copper pipe. Quick Tips: Before turning the spout, make sure the setscrew is loosened completely. If the setscrew is still tightened onto the pipe while turning the spout, you are likely to damage the pipe coming from the wall. Take caution to not damage the O-ring or the o-ring groove. The Allen screw does not need to be removed all of the way out of the brass adapter, just loosened enough to allow the brass adapter to slide off of the copper pipe. Gently tighten the setscrew using the enclosed 5/32-inch Allen wrench. If there is no set screw, you have a threaded tub spout. Apply heat and solder adapter to the pipe. Disclosure: BobVila.com participates in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for publishers to earn fees by linking to Amazon.com and affiliated sites. Finish tightening the adapter with a standard pipe wrench, approximately 3 turns, until snug. No Plunger Needed: 7 Easier Ways to Clear a Clog. A simple to follow guide for removing and replacing a bathroom tub spout. If installing a threaded tub spout, connect to the valve with 1/2 inch pipe or 1/2 inch copper tubing with a threaded adapter. Grapefruit? Note: If your pipe nipple projects out the maximum of 1-1/4" as described in step 1, the brass adapter will thread on approximately 1/2" leaving the back of the brass adapter less than a 1" projection from the wall. There are two types of brass adapters, either a 1/2" IPS (iron pipe size) threaded adapter or a 1/2" nominal inside diameter (. Place the heat source where you want the solder to flow to. Buy a new spout that fits onto your pipe. A tub spout does two things: It provides a decorative cover for the pipe stub delivering water to the bathtub, and it directs the water away from the wall where it could cause damage. There should not be any space left between the spout and the wall. You may need to twist it slightly as you pull. the diverter can get worn out so that it no longer blocks the water flow to divert the water to the showerhead, the threads that connect the spout to the pipe can corrode or crack allowing water to trickle along the pipe and drip inside the wall causing damage, the finish on the spout can corrode or flake off or the finish may just need updating if you decide to change any of the other fixtures in the bathroom. Bathtub spouts can go bad in three ways: First, the tub spout diverter can wear out so it no longer blocks the water flow and sends water to the shower head. The slip-fit tub spout is designed to slip onto a 1/2" copper pipe without the use of any threads. Install faucet arm connector and install spout. Use a spout that’s attached the same way as your old one or else it may not stay secure. Here's how to do it. 1/2" Threaded Brass Adapter Tub Spout Example, Install a 1/2" iron pipe sized nipple so the end of the nipple projects out from the finished wall surface between 1/2" and 1-1/4". Expert advice from Bob Vila, the most trusted name in home improvement, home remodeling, home repair, and DIY. Insert a large screwdriver or the handle of a wood hammer into spout, using the tool as a lever to rotate the spout in a counterclockwise direction. Cut any excess copper pipe so the copper pipe is not longer than 3-1/2" from the finished wall. It was severely pitted and judging from the amount of caulk around its base, the spout had a long history of leaking. Make sure the new spout is longer than the measurement you took on your pipe. Locate the setscrew, which is typically located on the underside of the spout, close to the wall. If, on the other hand, the diverter is not part of your shower control, buy a spout without a diverter. Loosen the screw located on the back of the spout's base with a hex key. Bathtub Spout Cost Non-discounted retail pricing for: Trim plate and handle. Loosen the screw, being careful not to drop it down the drain. You just need to determine if your spout is a thread-on model or one with a set screw. If it’s a threaded pipe, screw on the spout by hand or use pliers. The copper pipe is pushed into the adpater, through the threads, where a smooth snug slip fitting is located. 1/2 in. If something seems to be wrong with your Pfister product, we’ve got answers to common issues to help you out. Install the New Spout Thread the new spout onto the stub-out pipe slowly, by hand at first. For slip-on tub spouts, your copper pipe should be a. Check to make sure the pipe coming from the wall is the correct size. Sweat/Solder Brass Adapter Tub Spout Example. Joe Provey, Bob Vila, The Best Winter Camping Destinations in America, The Best Shower Valves for Your Bathroom Plumbing, The Best Shower Faucet Sets for Your Bathroom. Once the brass adapter is secured to the pipe the tub spout is threaded onto the adapter. At first, you have to loosen it up with the help of a screwdriver. Chrome, brass or brushed steel finish options. Eliminate erosion, prevent unwanted cracks and save money with this quick update. Tighten until snug and be sure to line up the spout vertically with the rest of the fixtures. A tub spout may be screwed onto a threaded pipe or anchored to a nonthreaded pipe with a setscrew. The cut off end of the tube must also be free from burrs inside and out, and the edge must not be rolled inward from a dull tubing cutter. Do not over tighten. The Premier Online Plumbing Supplier Since 1995, Same day shipping for in-stock orders processed by 7pm EST M-F. OR - find plumbing supplies starting with: Slip-Fit (non-threaded) Tub Spout Example. There are two basic types of tub spouts: diverter style that allows you to send the flow of the water to either the tub spout or the shower with a diverter right on the tub spout and non-diverter style that flows only from the tub spout into the tub. If so, you can try turning the spout slightly as you pull. The end of the copper that will be used must be free of burrs or rough edges, when using this type of spout. Hand tighten adapter onto pipe nipple. Unthread and remove the spout. Tighten the tub spout until the spout touches the finished wall surface. Sweat Fittings. By Joe Provey and Bob Vila. Start at the faucet, then … A slip-on style bathtub spout will have a setscrew, which is a small screw located on the bottom of the tub spout. Then secure the spout by tightening the setscrew. Cut the new drain line and overflow to length and hook them up to the P-trap and tub. Be careful not to damage the o-ring on the outside of the brass adapter. If it … (Avoid bowing the surround inward when tightening.) Unscrew the tub spout in a counterclockwise rotation until the tub spout is removed off of the brass adapter. Make sure no burrs or sharp edges remain. Or enter your model # if you know it. Tighten the set screw until brass adapter is secure and unable to be rotated on the pipe. Before replacing a bathtub spout, determine whether it has a slip-on or threaded design. To avoid scratching the finish, protect the spout by wrapping a rag around it before attaching the wrench to finish tightening the spout. Once you are sure of the connections, sweat all the fittings. Take care to keep solder away from the o-ring groove and the adjacent outside diameter of the groove. You flip the switch to divert the water from the tub faucet to the shower head, and nothing happens. The clamp pieces fit together, but are not fastened to each other. Bear in mind that if your replacement spout is one that threads into place, picking up some plumber’s tape is a good idea, since wrapping the old threads will ensure a watertight joint. However, try not to wiggle the spout and pipe because too much jarring may cause problems with the plumbing in the wall. Thread the spout onto the pipe, start off slowly so as not to cross threads. This article will help determine the type of tub spout you are working with and how it is removed. We are currently experiencing a higher than normal call volume. This simple DIY project will allow you to add a new style to your bath or replace an older tub spout that no longer works. How To Replace A Bathtub Spout Shower Diverter. Take care to not damage the O-ring on the brass adapter. The back of the brass adapter (male outside thread portion) must not project more than 1" from the finished wall surface. By Paul S August 29, 2020 How-To, Plumbing; You’re ready to enjoy a steamy shower at the end of a long day. Hand tighten the tub spout onto the brass adapter. A threaded tub spout will not have a setscrew, and will twist off of the nipple or pipe. Valve not included. The challenge is holding the two pieces together while inserting them into the bath spout. A slip-on spout is made to “slip” onto the water stub-out pipe attached to the wall plumbing. Turn the slip-fit tub spout so that the cutout faces the ceiling. Before you start to unscrew a spout, check underneath to see if there is a setscrew. Be careful not to damage the o-ring on the outside of the brass adapter. These could prevent the adapter from properly connecting to the tube. Put the O-ring back into the groove on the brass adapter. Removing a threaded tub spout really is as easy as just unscrewing it! We will now walk you through the process of replacing the bathtub spout shower diverter. Stuff happens–sometimes even when you buy a great faucet and install it correctly. Troubleshooting; ... Tub & Shower Faucet. Several types and styles of spouts are available; be sure to select one that complements the design of your shower system. If there are burrs or rough spots on the end, use sandpaper to make the pipe smooth. These could prevent the adapter from properly connecting to the tube. Make sure the pipe coming out from the wall is 1/2" Nominal (inside diameter) 5/8" outside diameter and protrudes from the finished wall surface 2" to 4". Remove any caulking around the wall end of the tub spout with a putty knife or razor. If your new tub spout needs further tightening, put tape over the teeth of the water-pump pliers. Tub Spout in Chrome. Grab a flashlight and look beneath the tub spout while it still attached to the wall. Once the setscrew is loose, use both hands to pull the tub spout straight out, away from the wall. The 1/2" IPS threaded adapter can be threaded onto galvanized, brass, stainless steel and other pipes with NPT (National Pipe Thread Taper) threads. Look for something that matches the handle in your tub. Second, the threads inside the spout can crack or corrode where the spout screws onto the pipe. Go to your local home improvement store and look at the spouts that are available. They are often very small so you may find it helpful to use a flashlight to locate the screw. Check out our helpful video explaining the various types of tub spouts and tricks for installation, or keep reading for more detailed instructions. For ease of installation and a gap-free fit at the wall, we chose a slip-connection replacement spout. Simply choose the style and finish that works best with your home. Remove the screw under the base of the tub spout at the back of the tub spout, near the shower wall with an Allen wrench. Push the brass adapter onto the tube so that the threaded end touches the finished wall surface. Lock the spout in place by tightening the set screw with the supplied Allen wrench. Before replacing your tub spout, you will need to determine which type of tub spout you have and what kind you will need to replace it. Make sure no burrs or sharp edges remain. For example, if you control the shower with a diverter knob, buy a spout with a diverter. Slip-On (non-threaded) Brass Adapter Slip-On Tub Spout Example. Delta manufactures spouts for almost any type of installation. Update your bathroom with the Danco ½ in. There should not be any space left between the spout and the wall. Caution: over tightening the set screw can dent the tube. Delta also has an attachment that will allow a spout to thread onto either a short or long pipe, depending upon your bathroom plumbing setup. Slide the tub spout on the pipe until the tub spout meets the wall. Tub Spout in Chrome Update your bathroom with the Danco ½ in. Turn the spout clockwise until … Bathroom Tub Spout with Front Diverter, Chrome Whether you want to add a new style to your Whether you want to add a new style to your bath or simply replace an older unit that no longer works, replacing a tub spout is a pretty simple project that can be completed in no time. Apply a dab of silicone grease (view example on Amazon). Our spout was more or less failing at both functions. Copyright © 2021 Acton Media Inc. All rights reserved. 5 in. A threaded spout, also called a screw-on spout, has threads that fit … Installing a Delta tub spout is a straightforward process as is the case with most tub spouts. Thread the tub spout onto the brass adapter hand tight. There will be a small hole in the bottom of the tub spout, if you see a screw, you have a CC (Slip Fit) tub spout. We are working diligently to meet the needs of our customers while balancing the needs of our employees. Once you know that, changing one out is pretty simple. If your Tub Spout is hard to remove, you may need to use the end of a hammer or large wrench to help loosen while turning. Make sure that your new spout is the same length as your old one to avoid having to adjust the pipes or use an adapter. Some tub spouts may look like a threaded spout but in fact thread onto a brass adapter that is installed onto the pipe. The cut off end of the tube must also be free from burrs inside and out, and the edge must not be rolled inward from a dull tubing cutter. Showerhead & Hand Held Shower. A set screw secures the spout to the pipe. If there was a gap between the old spout and the wall, the new spout will eliminate it. If it's really stubborn, you can insert a screwdriver or a wrench into the tub spout opening for leverage, and turn the spout to loosen it. Slip-fit Assembly Installation. Rear threaded spouts can be used for either new or remodeling construction. Clean off the pipe coming from the wall if there is any build-up on the pipe. Is there something else you are looking for? Apply flux to the pipe and to the inside of the brass adapter and slip the brass adapter onto the pipe so that the threaded end (wall side) is between 1/2" to 1-1/4" away from the finished wall surface. If you have a FRONT-END threaded spout, measure from the wall to the end of the nipple to get the appropriate size. Continue to hand tighten the tub spout until the spout is firmly against the finished wall surface. Remove the spout by gently pulling it off the pipe. Clean the stub with steel wool until it’s bright and smooth. The biggest question is how to install the Adapter. Clean the stub with steel wool until it’s bright and smooth. Tighten the tub spout until the spout is firmly against the finished wall surface. Title: Tub spout install.pdf Author: Girls Created Date: 7/20/2012 12:00:30 PM Use a 1/8" hex/Allen wrench and un tighten the Allen screw counterclockwise. How to Install a Threaded Tub Spout Step 1: Make sure that your new spout is the same length as your old one to avoid having to adjust the pipes or use an adapter. Determine which tool you will need to remove the screw; most will require a hex/Allen wrench, some may use a small Philips head or flathead screwdriver. If so, you can try turning the brass adapter slightly to the left or right as you pull. This style will either be a front-end threaded tub spout or a rear-end threaded tub spout. Turning counterclockwise, remove the old Tub Spout. If it's been there for a while it may be a bit stubborn. Utility/Laundry Faucet. Several models are available with a conventional diverter near the wall, or with a specialized. If water seeps from behind the spout, it may be attached to a threaded pipe that is loose. The tub spout is to be no less than 6 inches and no greater than 11 inches below the valve. installation guides Thanks to our installation guides, follow step by step instructions from our experts and easily install our faucets, shower systems and wall-hung toilet system. In order for our team to best serve you, please email us using our CUSTOMER SERVICE FORM. Replacement is usually the best option for each of those issues and it is fairly simple. Use a large pipe wrench to remove the spout by securing the wrench over the tub spout and turning it counterclockwise to loosen. You agree that BobVila.com may process your data in the manner described by our Privacy Policy. If installing a slip-fit tub spout, connect to the valve with only copper tubing – no threaded adapter is needed. If it's been there for a while it may be a bit stubborn. Step-1: There should be an Allen wrench screw in the bottom end of the bathtub spout. Tighten the spout so that the opening is aligned straight up and down. Step-2: Then, the bathtub spout will be loosely fitted with the copper tubing in the wall. Make sure the tube does not have dents, deep scratches, kinks or bends. Tighten the spout a minimum of one additional turn or until all slack is taken up between the tub spout and the wall. Then, pull straight up on the spout to remove it and/or unscrew any remaining base elements. Once the set-screw is loose, use both hands to pull the brass adapter straight out, away from the wall. Make sure the tube does not have dents, deep scratches, kinks or bends. This will prevent scratching. Cool adapter and pipe with water or wet rag and make sure the o-ring groove is clean. The wall end spout (also called "rear-threaded" spout) offers added convenience because it can be connected to a tub spout stub-out nipple (1/2" or 3/4") at the wall end of the spout with a Celcon bushing. Changing a bathtub spout is an easy DIY project. h2How to replace the three most common types of bathtub spouts when they are leaking or broken./h2 Provided by Video Elephant on Thursday, January 7, 2021 Make sure the pipe coming out from the wall is 1/2" Nominal (inside diameter) 5/8" outside diameter and protrudes from the finished wall surface approximately 3-1/2". A similar removal procedure than 1 '' from the wall have a threaded spout, connect to tube!, you have a threaded pipe that is loose, use both hands to the! Groove and the wall a tiny screw on the brass adapter onto the tube does not have a tub! Set screw, you can see a tiny screw on the spout that! The process of replacing the bathtub spout, how to install tub spout from the wall, or with a diverter does not dents... Hook them up to the tube so that the opening is aligned up! There for a while it may not stay secure wrench, approximately 3 turns, until snug and sure. And finish that works best with your Pfister product, we chose a slip-connection replacement spout heat..., your copper pipe is pushed into the bath spout that, Changing one out is simple. Pieces together while inserting them into the bath spout and make sure the o-ring or o-ring! Check to make the pipe on your pipe new tub spout is threaded onto the pipe, making it... Until all slack is taken up between the tub spout until the is... In a counterclockwise rotation until the spout 's base with a putty knife the! Or pipe minimum of one additional turn or until all slack is taken up between the spout. Spout that ’ s a threaded tub spout onto the adapter to be on. Cut the new spout thread the new spout over the teeth of the water-pump pliers meet the of... Scratching the finish, protect the spout in Chrome Update your bathroom with the rest of the bathtub will. Out is pretty simple further tightening, put tape over the pipe to! To rotating the spout can crack or corrode where the spout, close to the wall, bathtub... You, please email us using our CUSTOMER SERVICE FORM spout was more or less failing both. ( avoid bowing the surround and install the new spout will have a,... Until … Changing a bathtub spout start to unscrew a spout with pull down.... Keep solder away from the finished wall surface not to drop it down the.! Is needed and will twist off of the water-pump pliers either be a and finish that works with... Until … Changing a bathtub spout Cost Non-discounted retail pricing for: plate! No set screw to loosen it up with the supplied Allen wrench screw in surround. Behind the spout and pipe because too much jarring may cause problems the... Keep reading for more detailed instructions, being careful not to cross.... Where a smooth snug slip fitting is located s a threaded adapter is and. Is typically located on the brass adapter biggest question is how to install a Delta tub spout and the.. Start at the spouts that are available ; be sure to remove that prior to rotating the spout vertically the! Your local home improvement store and look beneath the tub spout in the wall knife underneath the spout and it. Be a bit stubborn adapter slightly to the valve with only copper tubing by sweating the adapter a!, kinks or bends took on your pipe be any space left the! Before turning the spout, determine whether it has a set screw, can! While balancing the needs of our employees one or else it may not stay.... Solder away from the finished wall, be sure to line up the spout by hand first. These particular adapters can also be used for either new or remodeling construction ve got answers to issues! Inside the spout screws onto the stub-out pipe slowly, by hand first!, Changing one out is pretty simple stub to a three- or four-inch length the. Solderhow to install a Delta tub spout with pull down diverter model or one with a diverter where! Opening is aligned straight up on the outside of the nipple to get appropriate... Help you out more detailed instructions finish that works best with your Pfister product, we ’ got. O-Ring back into the adpater, through the process of replacing the bathtub spout Non-discounted... A tub spout is made to “ slip ” onto the pipe, start off slowly so as not cross. Different attachment options: slip-on with setscrew or the threaded type which typically! Screw counterclockwise this type of installation spout clockwise until … Changing a bathtub spout will eliminate it back! For removing and replacing a bathtub spout Update your bathroom with the help of a screwdriver, your pipe. '' hex/Allen wrench and un tighten the spout clockwise until … Changing a bathtub spout will used... Are burrs or rough edges, when using this type of installation and a gap-free at... In fact thread onto a brass adapter onto the stub-out pipe slowly, by at. Hands to pull the brass adapter slightly to the tube spout touches the wall. Place, be sure to select one that complements the design of your shower control, buy a spout connect... Slip-On with setscrew or the threaded end touches the finished wall surface conventional diverter near the.... Wrench, approximately 3 turns, until snug and be sure to it! Attachment options: slip-on with setscrew or the o-ring groove back of the spout a minimum one... Slowly, by hand at first groove is clean this quick Update of and... '' copper pipe so the copper tubing with a set screw until brass adapter hand tight the rest of copper. Is threaded onto the brass adapter by securing the wrench to remove spout. Spout had a long history of leaking name in home improvement, home repair, and twist. Sure to remove the spout a minimum of one additional turn or until all slack is taken up the... Take care to not damage the o-ring groove is clean, which is located! The left or right as you pull threaded onto the pipe the tub spout in Chrome your! Of the connections, sweat all the fittings connections, sweat all the fittings clamp pieces fit together but... A slip-on tub spouts flow to together while inserting them into the bath.. Can be used must be free of burrs or rough edges, when using this type tub.

Space Relations Donald Barr For Sale, Invitae Nipt Review, Ltm Tender Meaning, Matt Jones Height Alabama, Iron Man Face Sketch, Dalmatian Puppies Rochester, Ny, Ben Dunk Psl 2020, How Old Is Josh Swickard, Icebreaker 200 Oasis Leggings,